看到白色激光了！

LLED · 发表于 2009-5-6 03:36

马上注册，结交更多好友，享用更多功能，让你轻松玩转社区。

您需要登录才可以下载或查看，没有账号？注册成为会员，享受更多功能。

x

在网上看到的，是利用红蓝绿三种激光混合而成。很强大，很远射！
[size=+0][size=+0]

登录/注册后可看大图

[size=+0]

[size=+0]

登录/注册后可看大图

[size=+0]

[size=+0]

登录/注册后可看大图

[size=+0]

[size=+0]

[size=+0]

登录/注册后可看大图

[size=+0]

登录/注册后可看大图

[size=+0]

登录/注册后可看大图

[size=+0]First trial assembly
[size=+0]
[size=+0]

登录/注册后可看大图

[size=+0]

[size=+0]Making a pointer
[size=+0]To make this into a reasonably sized hand held I needed to turn the output through 90 degrees for this I used the turning mirror from the PS3 sled.

登录/注册后可看大图

[size=+0]

[size=+0]It needs to be stuck onto the optical block like this

登录/注册后可看大图

[size=+0]

[size=+0]Preparing the optical block

登录/注册后可看大图

[size=+0]

[size=+0]You will note that I did this before sticking the modules in place. To get a flat surface to mount the prism block you will need to cut, drill and bend the stainless cover that came off the back of the sled. This was carefully glued in place with Araldite.

登录/注册后可看大图

[size=+0]

[size=+0]The prism was then glued in place, I wired up the LD’s temporarily to make sure that I was gluing this on straight, it is held in place with Araldite.

登录/注册后可看大图

[size=+0]Once it had dried I used some more Araldite to fillet the edges to ensure a strong mounting.
[size=+0]

登录/注册后可看大图

[size=+0]
[size=+0]Powering it up
[size=+0]You may have concerns about powering this up as the modules have different polarities:-

[size=+0]Green positive case

[size=+0]Red negative case

[size=+0]Blu ray either polarity

[size=+0]I suggest to keep things simple that you supply the green from one set of batteries (3.6v) and the red/blu ray from another set (7.2v). If you go this route do not connect any part of either supply to the case of the finished laser and it will work fine.

Wiring diagram

[size=+0]

登录/注册后可看大图

[size=+0]Battery holder
[size=+0]I decided to use 2 supplies so built a battery holder for 2off
RCR123A and 1off CR123A, it is made from a piece of plastic tube cut down the middle.

登录/注册后可看大图

[size=+0]Spacers were cut from plastic scrap
[size=+0]Contacts were odd bits of brass sheet
[size=+0]1 spring came from the green module
[size=+0]The other was just knocking around

[size=+0]The whole lot was assembled with superglue and Araldite.

[size=+0]
[size=+0]

This will work together to give you this....

登录/注册后可看大图

[size=+0]
Further info on this build and many others may be found on Laser pointer forums
(direct link) http://www.laserpointerforums.com/forums/YaBB.pl?num=1229256424
A Vimeo movie of what it does may be found here:-http://www.vimeo.com/4131352

LLED · 发表于 2009-5-6 03:37

沙发我占！{:1_217:}

LLED · 发表于 2009-5-6 03:37

消灭板凳！

LLED · 发表于 2009-5-6 03:37

消灭地板！

UFO-123 · 发表于 2009-5-6 03:37

不错，几十万呢？

wlbx · 发表于 2009-5-6 08:38

楼主可以查一下激光的定义，白色激光这个词用得不准确。

andyapple · 发表于 2009-5-6 09:00

哪张图片是它发白光了？

SNAKELB · 发表于 2009-5-6 09:31

看看

brucejiang · 发表于 2009-5-6 09:34

就是太贵了！

海天 · 发表于 2009-5-6 14:26

很好，很强大

海天 · 发表于 2009-5-6 14:26

很好，很强大

六月 · 发表于 2009-5-6 14:56

这么耀眼!!

andyapple · 发表于 2009-5-6 15:10

这个尤物的成本多少钱啊？

56255 · 发表于 2009-5-6 15:12

估计看到价钱我就能晕倒················

djdshp · 发表于 2009-5-6 15:21

不错

Q4877 · 发表于 2009-5-6 15:57

不错

nayubogen · 发表于 2009-5-6 22:19

提示: 作者被禁止或删除内容自动屏蔽

nayubogen · 发表于 2009-5-6 22:26

提示: 作者被禁止或删除内容自动屏蔽

andyapple · 发表于 2009-5-6 22:54

真的很像啊。{:1_232:}

9527 · 发表于 2009-5-6 23:15

第1.2张图巨像光头·~

		自动登录	找回密码
密码			注册成为会员，享受更多功能。

nayubogen nayubogen 当前离线积分 5210 IP卡狗仔卡头像被屏蔽该用户从未签到	发表于 2009-5-6 22:19 \| 显示全部楼层提示: 作者被禁止或删除内容自动屏蔽

	回复使用道具举报显身卡

nayubogen nayubogen 当前离线积分 5210 IP卡狗仔卡头像被屏蔽该用户从未签到	发表于 2009-5-6 22:26 \| 显示全部楼层提示: 作者被禁止或删除内容自动屏蔽

	回复使用道具举报显身卡