[转帖]CPF上的强人改的ARC-AAA

bangbang · 发表于 2006-6-4 11:19

马上注册，结交更多好友，享用更多功能，让你轻松玩转社区。

x

这个改装是用一个叫"<a href="http://www.candlepowerforums.com/vb/showthread.php?t=112678" target="_blank" >mini-FLuPIC by goldserve</a>"的电路改装而成的goldserve应该是一个强人吧...电路的贴我就不转了 引一下电路的照片 <img src="http://img348.imageshack.us/img348/3830/imgp03878ac.th.jpg"> <a href="http://img239.imageshack.us/my.php?image=arcsandwhich0xb.jpg" target="_blank" ><img src="http://img239.imageshack.us/img239/4351/arcsandwhich0xb.th.jpg" alt="" border="0"></a> <img src="http://img140.imageshack.us/img140/3042/imgp03786qr.th.jpg"> 
直径10.55mm, 1.6mm 厚 
特点是 1 LDO regulator,最适合用在AAA或纽扣电池的手电改装 Driver Topology: A low drop out (LDO) regulator limits the maximum
output current to around 500mA. The LDO regulator is PWM enabled by a
microcontroller. 驱动拓扑:这个电路的输出电流大概控制在500ma(有些专业词语不会翻译,见谅) 
There are three output levels. Two levels are selectable from 5-100% in 5% increments (20 levels) and the third is full on. This driver also also has Strobe and SOS. There are 5 menu modes - normally, you choose a mode and leave it there (I prefer mode 4). 这个电路有三级输出,两级为从5%到100%以5%选择性增加(应该是调光的幅度吧?)和第三级全亮.这个驱动还有"Strobe"和"SOS"功能.还有四总模式可供选择. <img src="http://img186.imageshack.us/img186/4808/flupicrevasml3mc.jpg"> 
All board sizes are $20 
Please add $3 for shipping outside of North America. Delivery confirmation is available for $6 for North America and $11 outside of NA. I can not be responsible for postal screw ups! 该电路是20元美金(不知道是美金还是加币,做电路的人好像是在多伦多,唉,为什么在加拿大的时候没有早点迷上手电.要不就可以收了) 邮费是11美金(或加币) 如果是加币的话..连邮费作者的报价就大概是120元人民币. <img src="http://img126.imageshack.us/img126/9171/img12320ab.th.jpg"> 
 
Old pill and new driver board. The board needs about 0.5mm removed from the diameter to fit snugly. 老灯头和新的电路的合照,电路需要磨掉大概0.5mm(直径).就刚好能放进灯头 <img src="http://img210.imageshack.us/img210/2299/img12081gp.th.jpg"> 这个是磨掉以后的图 <img src="http://img216.imageshack.us/img216/9929/img12182tq.th.jpg"> <img src="http://img216.imageshack.us/img216/2691/img12175ku.th.jpg"> 低亮和中亮测试 <img src="http://img210.imageshack.us/img210/5858/img12279pe.th.jpg"> <img src="http://img126.imageshack.us/img126/6858/img12288qe.th.jpg"> 
Head - before and after bevel of first ridge inside the lip. 仔细看看..灯头改装过...磨成了有一定斜度..原文自己看了..不大会译 打磨成一定斜度是为了避免碰到电路的插针作者在边都做了"环氧"使其绝缘.. <img src="http://img108.imageshack.us/img108/6600/img1209c4nd.th.jpg"> <img src="http://img126.imageshack.us/img126/245/img12529pq.th.jpg"> <img src="http://img210.imageshack.us/img210/9724/img12584pl.th.jpg"> <img src="http://img126.imageshack.us/img126/8057/img12596kr.th.jpg"> <img src="http://img126.imageshack.us/img126/9502/img12394rp.th.jpg"> <img src="http://img517.imageshack.us/img517/7841/img12697os.th.jpg"> 原来的光杯被打磨的更具抛物线 <img src="http://img487.imageshack.us/img487/7933/hs013co.th.jpg"> 大家猜一下作者用什么来做散热底座..嘿嘿... <img src="http://img462.imageshack.us/img462/4061/hs066pt.th.jpg"> <img src="http://img462.imageshack.us/img462/5250/hs082ou.th.jpg"> <img src="http://img462.imageshack.us/img462/5250/hs082ou.th.jpg"> <img src="http://img487.imageshack.us/img487/6371/hs093jr.th.jpg"> <img src="http://img462.imageshack.us/img462/6489/hs101os.th.jpg"> <img src="http://img462.imageshack.us/img462/1484/hs117jr.th.jpg"> <img src="http://img462.imageshack.us/img462/5093/hs120wq.th.jpg"> <img src="http://img487.imageshack.us/img487/9435/hs138sj.th.jpg"> <img src="http://img462.imageshack.us/img462/7282/hs149mt.th.jpg"> <img src="http://img487.imageshack.us/img487/9525/brdgndtab4on.th.jpg"> 作者为了使散热片做厚一点,就做了两块,焊起来,然后再磨平.... 噢..铜片是用一美分来做的...哈哈...仔细看看还能看到图案上的石柱... <img src="http://img462.imageshack.us/img462/9783/emitterremoval10dw.th.jpg"> <img src="http://img462.imageshack.us/img462/9767/emitterremoval29ap.th.jpg"> <img src="http://img487.imageshack.us/img487/6981/boardremovalpulltab6gd.th.jpg"> 作者还教人怎么拆..嘿嘿... <img src="http://img487.imageshack.us/img487/4416/assembledhead2yw.th.jpg"> <img src="http://img126.imageshack.us/img126/2749/head23ss.th.jpg"> 装好之后的灯头(怀疑还能防水么....) <img src="http://img487.imageshack.us/img487/8516/beam1low6lj.th.jpg"> <img src="http://img487.imageshack.us/img487/1073/beam2med0jd.th.jpg"> <img src="http://img462.imageshack.us/img462/5663/beam3high9fx.th.jpg"> 原ARC(用新的日亚CS LED的) 和改后的低,中,高亮对比图...(左边是ARC) 续航测试...这段我不译了...大概就是讲了续航时间还不错.测试100%亮度的时候,还用风扇对着吹..(放冰箱里面就好啦....他赶着上班没有测试完嘿嘿... 我把重点点红好了... Run-Time Test High (100%) and Medium (50%). I had a fan blowing on the
light for the 100% test but not the 50% test. I ran out of time to do a
10% test, but I plan on running one. I expect about 5+ hours for the
10% test. I have mine set at 10% - great for night nav around the
house. The behavior at the end of the curves (the rise in output) are
typical for this type of LDO regulator and consistant with my previous
tests. 
<a href="http://img508.imageshack.us/my.php?image=miniflupictx0harcaaa7rj.jpg" target="_blank" ><img src="http://img508.imageshack.us/img508/5949/miniflupictx0harcaaa7rj.th.jpg" alt="" border="0"></a> 
 
I added a 10% run to this graph. I ended the test after 8 hours (it was
late, I was sleepy, I had to go to work in the morning and I didn\'t
want to run the risk of over-discharging the Li-ion). I checked the no
load voltage on the Li-ion after the 8 hours and it read 3.79xxV (I
forget what the xx was - didn\'t write it down). I believe 3.8V
corresponds to around 30% of battery life remaining. 
<a href="http://img207.imageshack.us/my.php?image=miniflupictx0harcaaa4ta.jpg" target="_blank" ><img src="http://img207.imageshack.us/img207/1305/miniflupictx0harcaaa4ta.th.jpg" alt="" border="0"></a>

bangbang · 发表于 2006-6-4 11:25

该贴从下面连接转的... 
http://candlepowerforums.com/vb/showthread.php?t=114423 
作者Chimo.已经做了成品卖... 售价是100美元(或加币) 包邮费(不知道包不包到中国)..用的是加拿大邮政,还上了保险...以前就用过CaPost一次.忘了要多少米了.. 
COST: The cost is $100 which includes worldwide shipping by Canada Post (Small Packet - Air and includes CAN$100 insurance). 不知道有没有兄弟能帮买..如果是100加币的话,我一定收一只...就是不知道防水性如何了...

飞长爱你 · 发表于 2006-6-4 12:24

提示: 作者被禁止或删除内容自动屏蔽

bangbang · 发表于 2006-6-4 12:31

美国哪有那么多规章制度..没看到烧国旗的都是一大把一大把的么... 再说...作者在加拿大..嘿嘿..改的是美分..嘿嘿.(加拿大和美国的1cent是通用的,基本上在加拿大你拿10个1Cent就会有一个是美分)

neodeemer · 发表于 2006-6-4 16:41

100美刀吧，在cpf上看见了
arc_aaa还是太小了，散热不好
还是改Aleph系列最好拉，还能用Z57按钮尾盖

电子迷 · 发表于 2006-6-4 19:22

一般强,算不上太强,因为只能用10440了,1AAA的碱性和镍氢都用不上了!

harley.w · 发表于 2006-6-4 21:44

散热是个大问题

bangbang · 发表于 2006-6-5 02:22

是不是一般强我就不知道了.反正我挺喜欢的.可惜中国没人做.呵呵.. 这里还有一个改装的可以用AL的...

3/4W, 1W, or 1.5 watt ARC AAA using alkaline(3/4W only), NIMH or Prim. Lith AAA cells

<hr rgb(209, 209, 225);" size="1">


The mod is $25 for 1-level for any ARC or Clone that is provided by the buyer and $35.00 for 2-levels. 
Subtract $3.00 from the base price if you provide the Lux you like. 
Add $10 if I provide just the ARC head. (The same as the one pictured
except that it has the stock reflector finish unless you add services);
it works with the new bodies. 
Add $3.00 if I provide the Clone. 
Add $35.00 if I provide the ARC or Peak. 
Add $6.00 for an R-bin Lux I (RV1H); otherwise it\'s a lottery pick ????? 
Add $12.00 if I provide a T-bin Lux III (TXOH) or any other that Photonfanatic may have in stock. 
Add $3.00 for a polished reflector (for ARC and Peaks only); mirror finish 
Add $10.00 for a parabolic cut reflector (for ARC and Peaks only); gives a little hotter hotspot. 
*Please specific power output to Lux on high; 3/4, 1, or 1.5 watts
output. ( the clone is only offered with 3/4 watt and single stage. 
*Shipping is $5.00 for Priority or $2 for First class. 
 
For the ARC clone the price is $28.00 for a single stage or if you want
a specific tint lux, add $9.00. I will use T-bin in place of R-bin for
tints that Photonfanatic has that I can\'t find in R-bins. If you have a
clone you want me to use, subtract $3.00 from the total price. e-mail
me at <a href="mailto:ericmiller614@hotmail.com" target="_blank" >ericmiller614@hotmail.com</a> to order, but don\'t send any payments to this address! My PP address is <a href="mailto:ericmiller123@yahoo.com" target="_blank" >ericmiller123@yahoo.com</a>, but only pay once I send you a conformation e-mail. 
 
 
Here\'s a some pics and comparisons to the L0P (on the left) to the ARC
3/4 watt with an RV1H lux. The runtime should be flatter and longer
than the L0P.

问多星 · 发表于 2006-6-8 04:05

这个ARC-AAA要改装成1AAA和10440兼容有何难？关键是没几个人买不值得改装没意思。。。浪费时间浪费精力。。。浪费。。。浪费。。。呵呵

bangbang · 发表于 2006-6-8 07:47

[em05]老大,你的口气是有点想找东西来量产的感觉嘛..嘿嘿... 其实最不值得改的地方是会破坏它的防水性,如果不是我就早就求你给我改了...

qwqywl · 发表于 2006-6-8 17:35

手电毕竟还是要用的，在这个档次的电筒如果防水性不好了，就没意思了！[em06][em06][em06][em06]

		自动登录	找回密码
密码			注册成为会员，享受更多功能。