LLED 发表于 2009-5-6 03:36

看到白色激光了！

在网上看到的，是利用 红 蓝 绿 三种激光混合而成。很强大，很远射！

http://rog8811.webs.com/kes400a-remove.jpg





http://rog8811.webs.com/kes400a-bdrill.jpg


http://www.rog8811.com/module%20mounts%20R&BR01.jpg





http://rog8811.webs.com/Blue%20module01.jpg





http://rog8811.webs.com/Red%20module01.jpg?0.0212652507386073



http://www.rog8811.com/module%20mount%20green%20adaptor01.jpg




http://www.rog8811.com/Green%20module02.jpg

First trial assembly


http://www.rog8811.com/Laser%20assembly01.jpg





Making a pointer
To make this into a reasonably sized hand held I needed to turn the output through 90 degrees for this I used the turning mirror from the PS3 sled.

http://rog8811.webs.com/prism%20thingy02.jpg?0.775452418943978


It needs to be stuck onto the optical block like this

http://www.rog8811.com/Prism%20on.jpg



Preparing the optical block
http://rog8811.webs.com/PS3%20cut%20down01.jpg


You will note that I did this before sticking the modules in place. To get a flat surface to mount the prism block you will need to cut, drill and bend the stainless cover that came off the back of the sled. This was carefully glued in place with Araldite.

http://rog8811.webs.com/with%20cover01.jpg



The prism was then glued in place, I wired up the LD’s temporarily to make sure that I was gluing this on straight, it is held in place with Araldite.

http://rog8811.webs.com/mount%20prism%20thingy02.jpg

Once it had dried I used some more Araldite to fillet the edges to ensure a strong mounting.

http://rog8811.webs.com/optics%20assy02.jpg?0.9813264854532824

Powering it up
You may have concerns about powering this up as the modules have different polarities:-
Green positive case Red negative case [*]Blu ray either polarity I suggest to keep things simple that you supply the green from one set of batteries (3.6v) and the red/blu ray from another set (7.2v). If you go this route do not connect any part of either supply to the case of the finished laser and it will work fine.


Wiring diagram


http://www.rog8811.com/wwfull%20circuit01.jpg








Battery holder
I decided to use 2 supplies so built a battery holder for 2off
RCR123A and 1off CR123A, it is made from a piece of plastic tube cut down the middle.

http://rog8811.webs.com/Battery%20holder01.jpg

Spacers were cut from plastic scrap
Contacts were odd bits of brass sheet
1 spring came from the green module
The other was just knocking around

The whole lot was assembled with superglue and Araldite.





This will work together to give you this....

http://rog8811.webs.com/whitebeam01.jpg

Further info on this build and many others may be found on Laser pointer forums
(direct link) http://www.laserpointerforums.com/forums/YaBB.pl?num=1229256424
A Vimeo movie of what it does may be found here:-http://www.vimeo.com/4131352

LLED 发表于 2009-5-6 03:37

沙发我占！{:1_217:}

LLED 发表于 2009-5-6 03:37

消灭板凳！

LLED 发表于 2009-5-6 03:37

消灭地板！

UFO-123 发表于 2009-5-6 03:37

不错，几十万呢？

wlbx 发表于 2009-5-6 08:38

楼主可以查一下激光的定义，白色激光这个词用得不准确。

andyapple 发表于 2009-5-6 09:00

哪张图片是它发白光了？

SNAKELB 发表于 2009-5-6 09:31

看看

brucejiang 发表于 2009-5-6 09:34

就是太贵了！

海天 发表于 2009-5-6 14:26

很好，很强大

海天 发表于 2009-5-6 14:26

很好，很强大

六月 发表于 2009-5-6 14:56

这么耀眼!!

andyapple 发表于 2009-5-6 15:10

这个尤物的成本多少钱啊？

56255 发表于 2009-5-6 15:12

估计看到价钱我就能晕倒················

djdshp 发表于 2009-5-6 15:21

不错

Q4877 发表于 2009-5-6 15:57

不错

nayubogen 发表于 2009-5-6 22:19

nayubogen 发表于 2009-5-6 22:26

andyapple 发表于 2009-5-6 22:54

真的很像啊。{:1_232:}

9527 发表于 2009-5-6 23:15

第1.2张图巨像光头·~
页: [1] 2
查看完整版本: 看到白色激光了！